Humminbird ns10 gps manual

Johnson Outdoors Family. Need something extra for your fish finder? Find top-quality transducers, mounts, cables, carrying cases, batteries, and installation hardware to help get the most out of your equipment.

Humminbird's vast cartography options allow you to plan out your fishing trip with unrivaled accuracy. Find the best fishing spots in freshwater or saltwater and don't waste your precious time in unproductive waters. When the equipment on your boat all works together, you spend less time adjusting and more time fishing. From your trolling motor to your fish finder and shallow water anchor, we created the One-Boat Network to help you do more of what you love to do.

This hardware includes 1, 2, 4, and 8 feet extension masts which allow mounting the receiver well above obstructions.

Page 7: Installing The Control Head 9. Insert the cable connectors into the corresponding numbered connector port on the NS The connectors are keyed to insure correct orientation.

Refer to Figure 9 Install the NS 10 on the gimbal bracket using the knobs supplied with the rubber washers on the inside of the gimbal bracket. Page 8 This will prevent the battery voltage to the NS 10 from becoming too low while starting the boat engine.

If you would like to flush mount your NS 10 additional hardware is available. Refer to section V Page 9 Plotter Range: This area displays the range in the specified units shown in the graphic area.

With these four buttons you can make men adjustments to tailor the NS 10 to your needs. Connections to the NS 10 The back of the NS 10 has a centralized connector area where all inputs and outputs are located Refer to Figure 9.

All cables and connectors are waterproof and use gold plated contacts to inhibit corrosion. The connectors are keyed to prevent reversed connection.

Page 11 GPS signal. When using DGPS there will be an indicator on your display. If the indicator is a hollow box the NS 10 is receiving information from the receiver. If the box is filled in then good information is being received. It does not supply sufficient current to power both the NS 10 and the Receiver and is not intended for use in normal operation. Page 13 The status screen, which is now shown supplies much information about the system operation.

Page 14 When a satellite is being tracked the icon will turn dark. After the position has been determined, the NS 10 will provide accurate information at speeds up to Knots. Page System Options If so, to save time you may want to turn the NS 10 off and back on again to initiate a warm start. All menus will be shown in this area. This will automatically prompt the adjustment menu. You must choose the group repetition interval. Refer to section X.

Page Display Contrast meters or more , therefore, using an existing TD number from a Loran unit in a GPS receiver will result in a very lare error. The light is set at intensity level 2 when the unit is turned on. There are nine zoom ranges available.

Page 23 Note: When using the two smallest zoom ranges, the graphics area will become a plotter only, with no map shown. The smallest zoom range is 0. The largest zoom range is the region map. You may change temporary waypoints to permanent waypoints. This can be used in emergency situations such as man over-board. The NS 10 precisely stores the location of your boat to accurately return to this location.

You may only PICK waypoints that are visible on the screen. Due to the accuracy of the NS 10, you may have stored several waypoints very close to each other. Although the unit is able to differentiate between waypoints only several feet apart, the range of map or plotter selected may be too broad to show the waypoint as separate ponts. A temporary route consists of your present position, and one or more waypoints. Page 28 Note: The course history line is not displayed when the PICK mode is on, but it is being recorded and will be displayed when the mode is turned off.

Page 29 Any waypoint may be permanently stored, changed, or deleted, by using the Select System. This is especially helpful if you plan to return to the same area in the future.

The NS 10 memory will hold up to permanent waypoints, as well as 99 temporary waypoints. The NS 10 will not allow you to assign an already used number and will default to the lowest available number. Use the keypad to enter your numerical coordinate for longitude. Note: It is not necessary to assign a symbol to a waypoint.

Humminbird Dimension 3 2M. Humminbird FF 4. Humminbird FFC 2. Humminbird FF 2. Humminbird Fishfinder 3. Humminbird HDR 1. Humminbird HDR 2. Humminbird ID Sixty 1. Humminbird LCR4X6 1. Humminbird LCR 1. Humminbird LCR 2M.

Humminbird LCR 2. Humminbird LCRW 2. Humminbird Legend 2. Humminbird Matrix10 12 2. Humminbird Matrix 15 2. Humminbird Matrix 25 5. Humminbird Matrix 35 5. Humminbird Matrix 47 2. Humminbird Matrix 47 Installation 2. Humminbird Matrix 55 65 2. Humminbird Matrix 67 3.

Humminbird Matrix 77 2. Humminbird Matrix 87 2. Humminbird Matrix 97 3. Humminbird Matrix FF Installation 2. Humminbird NS10 2. Humminbird NS25 2. Humminbird PC Connect 2. Humminbird PMax 1. Humminbird PMax 30 1. Humminbird Piranha1 2 IN 2.