Great planes stuka manual

Page 10 On the bottom of the wing, cut away the covering from the two servo bays and the landing gear mounting rails. Locate the plywood center wing joiner. Test fit it into the right and left wing halves. When fitting it into the wing, make sure that the joiner angles downward. Page 11 After the glue has cured, cut away the covering on the Be careful not to cut into the expose the two holes for the nylon wing bolts to pass surface of the wing sheeting.

Page Fuselage Assembly Glue the wing fairing in place on the wing with 4. Measure from the end of the stab to each wing tip and 6-minute epoxy. Page 13 How to cut covering from balsa. Use a soldering iron to cut the covering from the stab. Allow the iron to heat fully.

Use a straightedge to guide the soldering iron at a rate that will just melt the covering and not burn into the wood. Install a pin into the center of three hinges, then install one hinge in each of the slots in one of the elevator halves. Install the hinge until the pin is touching the leading edge of the elevator. Page 15 8. Insert the nylon bearing into the slot. Page Install The Engine 4. Once you have the engine properly positioned on the engine mount, mark the location of the engine mounting holes on the rails of the engine mount.

Page 17 2. Install four nylon landing gear straps to hold the 5. Slide the wheel and axle onto the landing gear wire.

Position the nylon straps using Position the axle and wheel as shown. Position the wheel the dimensions shown in the photograph. Page Install The Fuel Tank wire for the set screw to tighten onto. This flat spot will also 3. Install the fuel tank into the fuselage. Apply silicone prevent the axle from slipping on the landing gear wire. File sealant to the front of the tank to hold it to the firewall. Feed a flat spot on the axle for the wheel collar too. Page 19 5. Repeat step 4 for the other half of the elevator.

If there is any binding between the inner flap and the flap, you may be able to get a smoother operation if you put a slight bend in the steel pin. This should only be necessary if you do not get the hole for the brass tube in perfect alignment. Install the aileron by marking the location for the mounting screws with a felt-tip marker onto the wing.

On the bottom of the wing, cut away the covering from the two servo bays and the landing gear mounting rails. Cut away the covering in the top of the wing to reveal the holes that the servo leads come through. After cutting the hole, feed the string from inside of the wing through the hole. This will allow you to pull the servo leads through the wing after the two wing halves are joined. Locate the plywood center wing joiner. Test fit it into the right and left wing halves.

When fitting it into the wing, make sure that the joiner angles downward. When you are satisfied that the two wing halves fit well together, apply a liberal amount of minute epoxy to the joiner, the joiner box and the wing root ribs. Insert the wing joiner into one of the wings and then install the opposite wing onto the other end of the wing joiner.

Put a clamp onto the tab that extends forward from the center of the wing and use masking tape to hold the wings together while the glue is curing.

Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Great Planes. Almost Ready to Fly Wingspan: 70" [mm] Wing area: sq in [ Radio Equipment The Stuka will require a good 4—7 channel radio system or greater with 7 servos. Engine Recommendations The recommended engine size range for the Stuka is a.

Contact Product Support Instruction manual Contact Product Support Full-size plans Not available GPMA Wheel Pants. When you are satisfied that everything fits properly, use minute epoxy to join the two wing sections and glue the joiner into the wing box in the wings Be sure to use 6. Repeat steps 2 to 24 for the left wing panel. You can only view or download manuals with.

Sign Up and get 5 for free. Upload your files to the site. You get 1 for each file you add. Get 1 for every time someone downloads your manual. Buy as many as you need.

View and download manuals available only for. Register and get 5 for free. Upload manuals that we do not have and get 1 for each file. Get 1 for every download of your manual.

Buy as much as you need. Radio Equipment Engine Recommendations Check the Control Directions Set the Control Throws Balance the Model C.

Balance the Model Laterally Identify Your Model Charge the Batteries Balance the Propellers Beautiful full kit, complete with all the laser cut parts and full size plans.

Interlocking construction. There is no extra cost to you. Because my integrity and your satisfaction are very important to me, I only recommend products or services I use personally or would purchase, and believe will benefit my readers.

This income is used to help pay for this site. For more information please click here to see my affiliates disclosure document. RC Sound System Version 4. Can be glow engine or electric powered Top quality construction from laser cut balsa and ply Covered with a vinyl, printed covering that includes panel lines Full length cockpit with 2 pilots and instrument panel BIg hatch for easy lipo change and radio access Bolt on two-piece wing for easier transport Strong and light construction from balsa and ply Accurate scale outline Good flyer!

Quality hardware package included. Great Planes Rimfire 1. Wing shown removed for transportation purposes. Flaps and ailerons. Close up of flaps and ailerons. Wheel pants and leg fairings. Tail group and tail wheel. Nice take off. Hatch removed for Lipo replacement.

Flying inverted. Could be landing or taking off!